What tools do you need to fix a bike chain?

To fix a broken or bent chain, you will need to remove it from your bike AND remove the broken or bent links. To do that, you will need a chain breaker tool. In the video, we used the Park Tool Master Chain Tool, which is the best tool for the job.

Can I fix my own bike chain?

Unless you do a lot of mountain biking, it isn’t often that you’ll need to repair or change your bike chain. However, chains do break now and then, and being able to fix one on the street is no harder than fixing a flat tire if you are prepared. To fix a broken chain, all you need is a chain tool.

Can you use wd40 on bike chain?

All you need to do is rinse the bike chain to remove any mud and thick dirt. Spray the WD-40 Bike Degreaser onto the surface of your bike chain and give it adequate time to work. On top of that, the WD-40 Bike Degreaser can be used for the cleaning and degreasing of other moving parts as well.

How often should I change my bike chain?

The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same.

How do you take off a bike chain without the tool?

If your chain has a master link, remove the link by twisting it off with a pair of needle nose pliers. Press the nubs through to the other side to fully remove the link. You may need to use a hammer or wrench to tap the link so that it pops out allowing the chain to separate.

How much does it cost to fix a broken bike chain?

If you are not a handy person when it comes to servicing your bike, you may have to pay a visit to your local bike shop for a chain repair. Most bike shops will charge about $30 – $50 dollars depending on the bike shop, whether it’s a popular brand or a “mom & pop” shop.

How much does it cost to fix a broken chain?

Soldering a Broken Chain: $20-$230 If the chain on your favorite necklace breaks, you can fix it by getting it soldered back together. This will cost you anywhere from $20 to $230 depending on the type of metal and the area of the chain that needs to be soldered.

Why has my bike chain snapped?

Chains break for a host of reasons, but most common is wear. For example, if a chain has been ridden for 2500 miles, it will actually stretch out. Correspondingly, a ridden chain will be longer from link to link than a new chain. Combine all those factors, mix in one bad shift and you have a recipe for a broken chain.

How do you remove a chain without a master link?

If you have a standard chain with no master link: Seat the chain in the chain tool, with the pin of the chain tool aligned with a pin in the chain. Turn the handle of the chain tool until you push the pin out far enough that you can break the chain.

What is the best lubricant for a bike chain?

Best bike chain lubes – our picks

• Rock N Roll Gold.
• Silca Super Secret Chain Lube.
• Green Oil Wet Lube.
• Finish Line Wet.
• CeramicSpeed UFO Ceramic lube.
• Tru Tension All Weather.
• Molten Speedwax. Wax chains take a bit of extra work, but are well worth the effort.
• Squirt chain lube. High-performance, wax-based lube.

What household items can I use to clean my bike chain?

You can use hot water with dish soap, a solvent or a degreaser. Step 2 Place the removed bicycle chain into the pan or plastic tub. Soak the chain for one to two minutes. Step 3 Remove the chain from the cleaning solution.

How often should I lube my bike chain?

Bicycle Tutor recommends cleaning and lubricating your bike’s drive chain at least once every month to maintain optimal performance and protection. The chain and drivetrain are typically the dirtiest parts of your bike, and this dirt is bad news for bike longevity and performance.